Текст страницы
Polisher Machine
sary, remove road tar with a general cheaner
before polishing.
Also, remove excess grease spots, bug stains
etc.
Using liquid wax (Fig. C)
Apply three layers of liquid wax to the pol-
ishing pad (4). Do not apply wax directly to
the surface to be treated.The first application
should cover approximately 1/4 of the surface
to be treated. For the second and third appli-
cations of wax, use half the quantity stated
above. The polishing head will not be able to
absorb as much wax when reapplied.
Using paste wax (Fig. D)
Spread a teaspoon of wax evenly over the
entire surface of the nozzle (4). Use a spatula
or any flat object. Do not apply wax directly to
the surface to be treated.
OPERATION (Figs. E and H)
Place the polishing pad (4) on the pad (1). Ap-
ply wax to the polishing pad (4) as described
in the “Using Liquid Wax” and “Using Paste
Wax” sections above. To turn on the polisher,
move the switch (3) to side with the inscription
“I”.
To turn it off,move the on/off switch to the side
marked “0”.
Always start and stop the polisher on or
against the surface. Do flat surfaces first-
hood,trunk and roof. Cover areas quickly with
broad,sweeping strokes in a criss-cross pat-
tern (Fig. E).
►Do not press on the polisher. The machine
works best under its own weight rather
than under pressure.
►After flat surfaces are covered with wax,
do sides of he car. Hold the polisher as in
(Fig. F). It is not necessary to use a criss-
cross motion on doors and fenders.
►Remove the polishing attachment (4) and
hand polish all hard-to-reach surfaces:
under bumpers, around door handles, etc.,
as shown in (Fig. G).
►Remove the polishing pad (4) from the pol-
isher and install a clean finishing polishing
pad (purchased separately) as described
in the “Installing the Cover (Figure B)” sec-
tion above.
►Buff the wax in the same order it was ap-
plied. Use long, wide strokes in a criss-
cross pattern. Do not press hard, let the
polisher work under its own weight (Figure
H).
Before launch:
►Before connecting the tool to the power
source, make sure that the switch is in
good condition.
►Make sure that all parts of the tool are
intact and not damaged. Make sure all ac-
cessories are installed correctly.
►Make sure that the ventilation openings
are not blocked or blocked.
Using the tool
►Before use, make sure that the surface to
be treated is washed and free of dirt. Nev-
er use the tool on an uncleaned surface.
Particles or grains of sand left on the sur-
face may damage the finish when using a
polishing machine.
►Remove all jewelry (rings, bracelets, etc.).
Do not wear loose clothing. Tuck long hair
under the headdress to prevent it from get-
ting caught on rotating parts tool.
►Carry out work in a well-lit and well-venti-
lated area.
►Use a suitable wax or polish for the job.
►Always keep the polisher close to the
surface. This will make the machine work
more efficiently and will also prevent the
polishing compound from splashing out.
►Place the polishing attachment onto the
support pad, making sure it is securely
fastened.
►Apply the required amount of wax/polish to
the polishing pad.
►Without turning on the machine, spread
the compound over the surface you will
polish. This will prevent splashing and en-
sure even distribution of the composition
over the surface. When working with a
large surface, divide it into small sections
and process them in turn.
►Place the machine against the surface,
then turn it on at the lowest speed. Con-
tinue spreading the compound over the
surface to be polished. Hold the machine
firmly and maintain a stable position.
►Increase the speed and distribute the mix-
ture in straight lines. Make sure these lines
overlap 50%. Slowly move the machine
over the surface until the polishing com-
pound becomes clear or dry (depending
on the type of compound used).
►Use extreme caution when mechanically
polishing around or over sharp objects and
contours. It is very important to distribute
pressure evenly when polishing different
parts of the car body. For example, when
polishing the sharp edges of body panels
or the edges of the gutter along the top of
the body, apply light pressure.
►Clean any remaining compound with a
8