Текст страницы
EN
EN
Before Use
How to Use
4. Connecting with the Dreamehome App
Turn On/Off
Do Not Disturb (DND) Mode
the robot cannot be turned on after the battery is depleted, manually connect
the robot with the station to charge it.
6. Add the Cleaning Solution
Press and hold the power button for 3 seconds to turn on the robot. Place the
robot onto the base station, the robot should turn on automatically and begin
charging. To turn off the robot, remove the robot away from the base station
and press and hold the power button for 3 seconds.
When the robot is set to the Do Not Disturb (DND) mode, the robot will be
prevented from resuming cleaning and the power indicator goes out. The DND
mode is disabled by default at the factory. You can use the app to enable the
DND mode or modify the DND period. The DND period is 22:00-8:00 by default.
Wi-Fi Indicator
(1) Scan the QR code on the robot, or search "Dreamehome" in the app store to
download and install the app.
(2) Open the Dreamehome app, tap "Scan QR code to connect", and scan the same
QR code on the robot again to add the device. Please follow the prompts to finish
the Wi-Fi connection.
Note:
· The scheduled cleaning tasks will be performed as usual during the DND
(1) Remove the dust tank cover and pull out the auto-detergent compartment.
(2) Open the upper lid of the compartment and add the cleaning solution.
(3) Close the lid of the compartment, put it back into the base station, and then
reinstall the dust tank cover. The cleaning solution will be added automatically
while working.
period.
Fast Mapping
· Blinking slowly: To be
connected
· Blinking quickly:
Connecting
· On: Connected
· The robot will resume cleanup where it left off after the DND period expires.
QR Code
②
①
Spot Cleaning
Note:
After configuring the network for the first time, follow the instructions in the
app to quickly create a map. The robot will start mapping without cleaning.
When the robot returns to the base station, the mapping process has been
completed and the map will be saved automatically.
②
①
· Only 2.4 GHz Wi-Fi is supported.
· Due to upgrades in the app software, the actual operations may differ from
Note:
When the robot is awaiting, press briefly the button
to enable the spot
cleaning mode. In this mode, the robot cleans a square-shaped area of 1.5 x
1.5 meters around it and returns to its starting point once the spot cleaning is
completed.
Pause/Sleep
· The auto-detergent compartment can be filled up with cleaning solution for
the directions in this manual. Please follow the instructions based on the
current app version.
· If you want to reset Wi-Fi, repeat step 2 and then follow the prompts to finish
use. Do not add any liquid other than the officially-approved cleaning solution
to help prevent malfunction.
the Wi-Fi connection.
· To disconnect the device from Wi-Fi network, press and hold the Reset button
Robot Restarting
· Install the auto-detergent compartment until it clicks into place.
on the robot for 3 seconds.
When the robot is running, press any button to pause it. If the robot is paused
for more than 10 minutes, it automatically enters sleep mode. All indicators
on the robot will turn off. Press any button on the robot, or use the app to
wake up the robot.
7. Add Water to the Clean Water Tank
5. Connect the Robot to the Base Station
If the robot stops responding or cannot be turned off, press and hold the
power button for 10 seconds to forcefully turn it off. Then, press and hold the
power button for 3 seconds to turn the robot on.
Take out the clean water tank from the base station and fill up the tank with
clean water. Then install it back into the base station.
Note: If the robot is paused and placed onto the base station, the current
cleaning process will end.
Press and hold the power button on the robot for 3 seconds to turn it on. Place
the robot onto the base station with the mop assembly facing toward the
washboard. Then you will hear a voice notification when the robot successfully
connects to the base station.
Auto Resume Cleaning
If the battery is too low, the robot will automatically return to the base station
to charge. After charging to the appropriate battery level, it will resume
unfinished cleaning tasks.
Note: To use this function, please enable it in the app.
Note: It is recommended to fully charge the robot before its first use. When
Note: Do not add hot water into the water tank, as this may cause the tank to
become deformed.
8
9