Текст страницы
robot status indicator light flashes slowly.
The robot will then wait for a connection.
Notes:
in height, 0.4 m (1.31 ft) in width and
1.2 m (3.94 ft) in depth. Make sure that
the location has good WiFi coverage for a
better experience with the mobile app. Plug
in and make sure that the status indicator
light is on.
• If you cannot connect to the robot due to your router
configuration, a forgotten password, or any other
reason, reset the WiFi and add your robot as a new
device.
• To check the current WiFi connection status, press the
plugged in. Then, press and the robot
will automatically return to the dock for
charging. The robot is equipped with a
built-in high-performance lithium-ion
rechargeable battery pack. To maintain
battery performance, keep the robot
charged.
and buttons simultaneously.
B4-1—
B3-1—More than 1.2 m (3.94 ft)
B3-2—More than 0.75 m (2.46 ft)
B3-3—More than 0.4 m (1.31 ft)
3. Add Device
Dock status indicator light off, robot
power indicator light breathing:
Charging.
Note:
Open the Roborock app, tap the “Add
Device” or “+” button and add your device
following the in-app guide.
The robot may not be turned on when the battery
is low. In this case, place the robot to the dock for
charging.
Notes:
Connecting to the App
1. Download the App
• The actual process may vary due to ongoing app
updates. Follow the guide provided in the app.
• Only 2.4 GHz WiFi is supported.
• If the robot waits more than 5 minutes for a
connection, WiFi will be automatically disabled. If you
want to reconnect, reset the WiFi before proceeding.
Search for “Roborock” in the App Store
or Google Play or scan the QR code to
download and install the app.
Instructions for Use
C
C1 Filling the Clean Water Tank
Lift the clean water tank, open its lid, and
then fill it with tap water. After filling, close
the lid, lock the latch, and then put the
clean water tank back to the dock.
Notes:
Notes:
• If the power cord hangs vertically to the ground, it
may be caught by the robot, causing the dock to be
moved or disconnected.
• The status indicator light is on when the dock is
powered on, and off when the robot is charging.
• The status indicator light turns red if an error occurs.
• Place the dock on a hard, flat floor away from fire,
heat, and water. Avoid narrow spaces or locations
where the robot may be suspended in the air.
• Placing the dock on a soft surface (carpet/mat)
may cause the dock to tilt and cause docking and
departing problems.
• Keep the dock away from direct sunlight or anything
that may block the dock location beacon, otherwise
the robot may fail to return to the dock.
• Do not use the dock without clean water tank, dirty
water tank, dust container cover, disposable dust bag,
cleaning solution cartridge, or cleaning tray module.
• Maintain the dock according to the Routine
Maintenance. Do not clean the dock power cord and
charging contacts with a wet cloth or tissue.
• All docks are subject to water-based tests before
leaving the factory. It is normal that a small amount of
water remains in the waterway of the dock.
B4 Powering On & Charging
2. Reset WiFi
Press and hold
and simultaneously
until you hear the “Resetting WiFi” voice
message. The reset is complete when the
• To avoid deformation, only use cold water.
• If any water stains remain on the outside of the
water tank, wipe them with a soft, dry cloth before
reinstalling the tank.
• To prevent damage, do not add any disinfectant in the
clean water tank. To prevent a high concentration of
cleaning solution, add solution only to the cleaning
solution cartridge.
Press and hold
to power on the robot.
Wait until the power indicator light is
steady, and then place the robot in
front of the dock. Make sure the dock is
45