Текст страницы
C2 Adding Cleaning Solution
Press and hold
to turn off the robot and
complete the cleaning cycle.
The robot cannot be turned off when it is being
charged.
Note:
robot will automatically return to the dock. After
charging, the robot will resume where it left off.
• The robot will retract mop cloth mounts to clean the
carpet. You can also set the carpet as a no-go zone in
the app to avoid it.
• Before starting each cleaning task, make sure that the
mop cloths have been properly installed.
1. Remove the dust container cover, pull out
the entire cleaning solution cartridge by
its bottom handle, and then place it on a
hard, flat surface.
Note:
Enabling the Robotic Arm
Function
Spot Cleaning
To prevent the dust container cover from falling
and hitting the robot, remove the cover with both
hands, one on each side.
2. Open the lid of the cartridge and add
cleaning solution.
Press and hold to start spot cleaning.
Cleaning range: The robot cleans a 1.5 m
(4.9 ft) × 1.5 m (4.9 ft) square area centered
on itself.
When the robotic arm is in its compartment,
press and hold the
and
buttons to
enable or disable the robotic arm function.
Please use the robotic arm function via
Roborock app.
After spot cleaning, the robot will automatically
return to the starting point and wait for orders.
Note:
Note:
3. Close the lid and put the cartridge back
to the dock. Press the cartridge until you
hear it lock with a click.
When the robotic arm is emergency stopped or
paused, press and hold the
and
buttons to reset
the robotic arm.
Pause
Starting Cleaning
4. Install the dust container cover in place to
make sure the dust container is securely
sealed.
Notes:
When the robot is running, press
or to
pause it, press
to resume cleaning. Press
on a paused robot to send it back to the
dock.
Placing a paused robot on the dock manually will
end the current cleanup.
Note:
Emergency Stop and Reset
Press
to start cleaning. The robot will
plan its cleaning route and in each room,
it firstly draws out edges and then fills
the room in a zigzag pattern. In so doing,
the robot cleans all rooms one by one,
thoroughly and efficiently.
Notes:
• Make sure that the cleaning solution cartridge is
entirely removed before adding cleaning solution.
• To prevent damage, do not use any disinfectant and
only use cleaning solution recommended by Roborock
in the solution cartridge.
• After adding, the robot will automatically add cleaning
solution to the water for mop washing and robot
water tank refilling according to the preset ratio to
ensure optimal mopping performance.
• Cleaning solution is not included in the package.
Purchase one if needed.
• If no floor cleaning solution is used daily, you may skip
this step or disable Smart Cleaning Solution Filling
in the app.
Turning On/Off
If an emergency occurs when the robotic
arm is working, press the
button to
immediately stop all operations of the
robot. When the robot is emergency
stopped, press and hold the
and
buttons to reset the robotic arm. If the
robotic arm has picked up an object, it will
slowly put down the object and then retract
to its compartment. If the robotic arm has
not picked up any object, it will open its
Press and hold
to turn on the robot. The
power indicator light will come on, and the
robot will wait for orders.
• To make sure the robot returns to the dock
automatically, start the robot from the dock and do
not move the dock during cleaning.
• Cleaning cannot start if the battery level is too low.
Allow the robot to charge before starting a cleanup.
• Before cleaning, tidy cords (including the power cord
of the dock) and valuables from the floor. Loose
items may be dragged by the robot, resulting in the
disconnection of electrical appliances or damage of
cords and property.
• If cleaning is completed in less than 10 minutes, the
robot will clean the area twice.
• If the battery runs low during a cleaning cycle, the
46