Текст страницы
balance, vibrate excessively and may cause loss
of control.
8. Do not use a damaged accessory.
General
This part may be printed separately from the "General
Power Tool Safety Warnings".
In these safety instructions, terms such as grinding/
grinder, sanding/sander, wire brushing/wire
brush, polishing/polisher or cutting-off/cut-off
tool are selected as specified by the manufacturer.
These terms in the warnings and headings shall be
consistently used or deleted based on the selected
operations. The “and”/“or” conjunctions may be
used as appropriate.
If the power tool is intended only for one of the
listed operations, the heading of that section is
to be used for all warnings.
Safety instructions for all operations
Beforeeach use inspect the accessory
such as abrasive wheels for chips
and cracks, backing pad for cracks,
tear or excess wear, wire brush for
loose or cracked wires. If power tool
or accessory is dropped, inspect
for damage or install an undamaged
accessory. After inspecting and
installing an accessory, position
yourself and bystanders away from the
plane of the rotating accessory and
run the power tool at maximum no-load
speed for one minute. Damaged accessories
will normally break apart during this test time.
9. Wear personal protective equipment.
Safety warnings common for grinding,
sanding, wire brushing, polishing or
cutting-off operations:
1. This power tool is intended to function
as a grinder, sander, wire brush,
polisher, hole cutter or cut-off tool.
Read all safety warnings, instructions,
illustrations and specifications provided
with this power tool. Failure to follow all
instructions listed below may result in electric
shock, fire and/or serious injury.
2. Operations such as grinding, sanding,
Depending on application, use face
shield, safety goggles or safety
glasses. As appropriate, wear dust
mask, hearing protectors, gloves and
workshop apron capable of stopping
small abrasive or workpiece fragments.
The eye protection must be capable of stopping
flying debrisgenerated by various applications.
The dust mask or respirator must be capable of
filtrating particles generated by the particular
application. Prolonged exposure to high intensity
noise may cause hearing loss.
10.Keep bystanders a safe distance away
wire brushing, polishing, hole cutting
or cutting-off are not to be performed
with this power tool. Operations for which
the power tool was not designed may create a
hazard and cause personal injury.
3. Do not convert this power tool to
from work area. Anyone entering
the work area must wear personal
protective equipment. Fragments of
workpiece or of a broken accessory may fly
away and cause injury beyond immediate area of
operation.
11. Hold the power tool by insulated
operate in a way which is not specifically
designed and specified by the tool
manufacturer. Such a conversion may result
in a loss of control and cause serious personal
injury.
4. Do not use accessories which are not
gripping surfaces only, when performing
an operation where the cutting
accessory may contact hidden wiring or
its own cord. Cutting accessory contacting a
"live" wire may make exposed metal parts of the
power tool "live" and could give the operator an
electric shock.
12.Position the cord clear of the spinning
specifically designed and specified by
the tool manufacturer. Just because the
accessory can be attached to your power tool, it
does not assure safe operation.
5. The rated speed of the accessory must
accessory. If you lose control, the cord may
be cut or snagged and your hand or arm may be
pulled into the spinning accessory.
13.Never lay the power tool down until the
be at least equal to the maximum speed
marked on the power tool. Accessories
running faster than their rated speed can break
and fly apart.
6. The outside diameter and the thickness
accessory has come to a complete stop.
The spinning accessory may grab the surface
and pull the power tool out of your control.
14.Do not run the power tool while carrying
of your accessory must be within the
capacity rating of your power tool.
Incorrectly sized accessories cannot be
adequately guarded or controlled.
7. The dimensions of the accessory
it at your side. Accidental contact with the
spinning accessory could snag your clothing,
pulling the accessory into your body.
15.Regularly clean the power tool’s air
mounting must fit the dimensions of the
mounting hardware of the power tool.
Accessories that do not match the mounting
hardware of the power tool will run out of
vents. The motor’s fan will draw the dust inside
the housing and excessive accumulation of
powdered metal may cause electrical hazards.
5
EN