Инструкция жесткий диск Seagate SkyHawk AI

3.4 Drive mounting (стр. 22 из 33)

Бренд: Seagate

Страница 22 документа Жесткий диск Seagate SkyHawk AI. Раздел: Жесткие диски 3.5". Бренд: Seagate.

Карточка инструкции Категория Бренд
Страница 22 из 33
Открыть на весь экран Открыть PDF

Текст страницы

www.seagate.com
Configuring and Mounting the Drive

3.4
Drive mounting

Users can mount the drive in any orientation using four screws in the side-mounting holes or four screws in the bottom-
mounting holes. Refer to Figure 2 for drive mounting dimensions. Follow these important mounting precautions when
mounting the drive:

•
Allow a minimum clearance of 0.030 inches (0.76mm) around the entire perimeter of the drive for cooling.

•
Use only 6-32 UNC mounting screws.

•
The screws should be inserted no more than 0.140 inch (3.56mm) into the bottom or side mounting holes.

•
Do not overtighten the mounting screws (maximum torque: 8 inch-lb).

Figure 2
Mounting dimensions (4TB & 3TB models)

3X 6-32 UNC-2B
3 MINIMUM THREAD DEPTH
0.14 MAXIMUM FASTENER
PENETRATION BOTH SIDES

Max: .795" or 20.20 mm
Alterntive: .783" .012" or 19.90 0.30 mm

4X 6-32 UNC-2B
3 MINIMUM THREAD DEPTH
0.14 MAXIMUM FASTENER
PENETRATION

Seagate SkyHawk Product Manual, Rev. A
21

Оглавление

SATA Product Manual 1
Seagate® Technology Support Services 6
1.0 Introduction 7
1.1 About the SATA interface 8
2.0 Drive Specifications 9
2.1 Specification summary tables 9
2.2 Formatted capacity 11
2.2.1 LBA mode 11
2.3 Default logical geometry 11
2.4 Recording and interface technology 11
2.5 Physical characteristics 12
2.6 Start/stop times 12
2.7 Power specifications 13
2.7.1 Power consumption 13
2.7.2 Conducted noise 13
2.7.3 Voltage tolerance 14
2.7.4 Power-management modes 14
2.8 Environmental specifications 15
2.8.1 Ambient Temperature 15
2.8.2 Temperature gradient 15
2.8.3 Humidity 15
2.8.4 Altitude 15
2.8.5 Shock 16
2.8.6 Vibration 16
2.9 Acoustics 17
2.9.1 Test for Prominent Discrete Tones (PDTs) 17
2.10 Electromagnetic immunity 17
2.11 Warranty 18
2.11.1 Data loss under power interruption with write cache enabled 18
2.11.2 Storage 18
2.11.3 HDD and SSD Regulatory Compliance and Safety 18
2.11.4 Safety certification 18
2.12 Corrosive environment 18
2.13 Seagate® Rescue™ Data Recovery Service 19
3.0 Configuring and Mounting the Drive 21
3.1 Handling and static-discharge precautions 21
3.2 Configuring the drive 21
3.3 SATA cables and connectors 21
3.4 Drive mounting 22
4.0 SATA Interface 23
4.1 Hot-Plug compatibility 23
4.2 SATA device plug connector pin definitions 23
4.3 Supported ATA commands 24
4.3.1 Identify Device command 26
4.3.2 Set Features command 31
4.3.3 S.M.A.R.T. commands 32

Похожие документы

Похожие документы по той же теме