Текст страницы
18 | English
Setting the operating mode
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Drilling
Changing the tool (see figure A)
u Remove the battery from the power tool before carry-
GSR 185-LI
Set the torque presetting ring (3) to the
"drilling" symbol.
GSB 185-LI
Set the operating mode presetting ring (4) to
the "drilling" symbol.
Screwdriving
GSR 185-LI
Set the torque presetting ring (3) to the re-
quired torque.
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
The drill spindle is locked when the on/off switch (10) is not
pressed. This makes it possible to change the application
tool in the drill chuck quickly, conveniently and easily.
Open the keyless chuck (2) by turning it in the direction of
rotation ➊ until the tool can be inserted. Insert the tool.
Firmly tighten the keyless chuck (2) by turning it by hand in
the direction of rotation ➋. This will automatically lock the
drill chuck.
Dust/Chip Extraction
GSB 185-LI
Set the operating mode presetting ring (4) to
the "screwdriving" symbol.
Set the torque presetting ring (3) to the re-
quired torque.
Impact drilling
GSB 185-LI
Set the operating mode presetting ring (4) to
the "impact drilling" symbol.
Switching on/off
To start the power tool, press and hold the on/off switch
(10).
The LED (8) lights up when the on/off switch (10) is lightly
or fully pressed, meaning that the work area is illuminated in
poor lighting conditions.
To switch off the power tool, release the on/off switch (10).
Dust from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one’s
health. Touching or breathing-in the dust can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.
Certain dust, such as oak or beech dust, is considered carci-
nogenic, especially in connection with wood-treatment ad-
ditives (chromate, wood preservative). Materials containing
asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the ma-
terials to be worked.
LED worklight with status indicator
u Avoid dust accumulation at the workplace. Dust can
easily ignite.
The LED worklight (8) is used as a status indic-
ator for device protection and low battery
status:
Operation
Description
LED
Feedback
Starting Operation
Flashing light 3x
during operation
Battery status is low.
The voltage level of the battery has fallen
below the optimum value. The perform-
ance of the device is restricted.
Inserting the battery
Note: The use of batteries unsuitable for your power tool can
lead to malfunctions or damage to the power tool.
Push the charged battery (6) into the base of the power tool
from the front until the battery is securely locked.
Flashing light 3x
during downtime
Setting the rotational direction (see figure B)
u Only operate the rotational direction switch (9) when
Device protection is active.
Device protection has been activated to
prevent the battery from consuming a
large amount of power and to protect the
device against damage.
– If the battery status is low, charge the battery (6) or re-
place the weak battery with a fully charged battery.
the power tool is not in use.
The rotational direction switch (9) is used to change the ro-
tational direction of the power tool. However, this is not pos-
sible while the on/off switch (10) is being pressed.
Right rotation: To drill and to drive in screws, press the
rotational direction switch (9) through to the left stop.
Left Rotation: To loosen and unscrew screws and nuts,
press the rotational direction switch (9) through to the right
stop.
Adjusting the speed
You can adjust the speed of the power tool when it is on by
pressing in the on/off switch (10) to varying extents.
A light pressure on the on/off switch (10) results in a low ro-
tational speed. Increased pressure on the switch causes an
increase in speed.
1 609 92A 8JT | (03.02.2023)
Bosch Power Tools