Текст страницы
Air Compressor
►In order to protect the product and the
Connect the hoses of the pneumatic tool.
Thanks to the compressor design, you can
connect two tools at the same time.
Before starting work, turn off the pressure
supply by turning off the pressure regulator.
Get ready for work
►Check the oil level before each use (see
operator from pressure increase when the
pressure switch fails, when the set pres
sure in the cylinder is exceeded, the safety
valve is used as a safety valve, and the
safety valve will release the excess pres
sure.
►To apply pressure to the tool, unscrew the
above). Top up if necessary;
►Move children and animals away from the
product at a distance of at least 3 meters;
►Make sure the hoses and tools are free of
damage that could cause air leaks;
►Wear protective equipment when working
with the connected tool (goggles, head
phones, gloves, respirator).
►Check the tension of the belt 9. The deflec
tion should be 10 - 15 mm when pressed
in the middle between the pulleys;
►Make sure that the belt pulleys rotate free
pressure regulator and set the desired
working pressure, and monitor it on the
pressure gauge.
Note! The compressor has two outlet fittings
equipped with pressure gauges.
The pressure in the receiver shows the pres
sure gauge located on the right, while the
pressure gauge located on the left shows the
outlet pressure, which you can adjust using
a reducer. The right fitting gives out com
pressed air with the maximum working pres
sure in the receiver, and the left fitting gives
out compressed air with the working pressure
set using a regulator.
►Air will automatically flow to the tool con
ly with little force, and be careful and safe
during this procedure.
Method of operation
Connect the product to the power source.
nected to the quick release connector.
►The operating pressure at the outlet can
►Before connecting the product to the
power source, make sure that the
switch is in the off position.
►In terms of electrical safety, this prod
be changed directly during the operation of
the regulator.
Note! When working with two tools at the
same time,and the air flow will be distributed
inversely proportional to the ratio of the flow
cross-sections of the tools.
►При необходимости смены рабочего
uct corresponds to class I protection
against electric shock, that is, it must
be grounded (a grounding terminal is
provided in the plug). If the plug does
not fit your socket, do not change the
plug. Instead, a qualified electrician
must install a suitable socket.
►To turn on the product, turn the switch to
the ON position (pull out the button).
►When the air pressure in the cylinder is
и н с т р у м е н т а , п о д к л ю ч е н н о г о
к б ы с т р о с ъ е м н о м у ш т у ц е р у –
п р о с т о о т с о е д и н и т е н е н у ж н ы й
более инструмент и подсоедините
необходимый.
The thermal protection of the electric mo
tor is installed on your product. In case of
overheating, the automation will turn off the
power supply to the electric motor and the
compressor will stop.
When the temperature returns to normal,
the compressor will turn on automatically.
►Also, a thermal relay is installed on your
lower than the switch setting value, the
product will automatically turn on. When
the switch pressure setting is reached, the
engine will also automatically shut down.
When the air accumulated in the cylinder
is consumed and the pressure drops to a
preset minimum value, the automatic de
vice will start the engine again.
►In this mode, the compressor starts and
product, which protects the product from
overloads and in the event of a thermal
fuse failure. When the protection is activat
ed, reset the relay by pressing the button.
Note! To avoid breakdowns or premature
failure of the product (especially with frequent
cases of self-shutdown), before turning it back
on, find out the reason for the protection oper
ation.
►When the compressor is stopped (auto
stops automatically.
Note! The maximum and minimum pressure
are preset at the factory. Self-regulating pres
sure can cause product failure. If you find that
the threshold pressure value is adjusted by
itself, you will be denied the warranty. If nec
essary, additional adjustments can be made
by experts in the service center.
matically or forcibly by the switch), the
6