Текст страницы
Calculation of horizontal distance with the help of tilt sensor
(Vector 80 only)
Calculation of distance by 3 additional measurements -
subtraction of 2 cathetuses (Pythagoras 3)
MESSAGE CODES
While operation, the following codes/symbols may appear on
the display:
Symbol will appear on the
Symbol will appear on the
Message
Problem
Solution
display. Laser beam will be on.
display. Laser beam is on.
Short
press
4 times.
Short press
5 times.
(Vector 60)
301
Distance is out of
range.
Keep in permissible
measuring range.
Short press
Take 1st measurement (hypotenuse).
Short press
7 times.
(Vector 80)
302
Reflected signal is too
weak.
Use a reflective plate.
303
Short press
Make
the
1st
measurement
(hypotenuse 1).
- tilt angle value (measured)
Short press
Make
the
2nd
measurement
(hypotenuse 2).
Measuring result
cannot be displayed
(negative or exceeds
99999).
Repeat measurements
until you get positive/
smaller measurement
rerult.
Short press
Make
the
3rd
measurement
(cathetus).
304
Pythagorean theorem
calculation error.
Make measurements in
correct succession.
- hypotenuse (measured)
- vertical distance (calculated)
305
Low battery.
Charge the battery.
306
Temperature is too low.
- horizontal distance
(calculated)
Warm up the
device to operating
temperature.
– hypotenuse 2 (measured)
– cathetus (measured)
307
Temperature is too
high.
Cool down the
device to operating
temperature.
Short press
Exit the mode.
308
Ambient light is too
strong.
Make measurements in
less illuminated zone.
– cathetus (calculated)
Calculation of distance by 2 additional measurements
(Pythagoras 1)
Short press
Exit the mode.
Symbol will appear on display.
WARRANTY
All CONDTROL GmbH products go through post-production
control and are governed by the following warranty terms. The
buyer’s right to claim about defects and general provisions of
the current legislation do not expire.
1) CONDTROL GmbH agrees to eliminate all defects in
the product, discovered during the warranty period, that
represent the defect in material or workmanship in full volume
and at its own expense.
2) The warranty period is 36 months and starts from the date
of purchase by the end customer (see the original supporting
document).
3) The warranty dösn’t cover defects resulting from wear
and tear or improper use, malfunction of the product caused
by failure to observe the instructions of this user manual,
untimely maintenance and service and insufficient care, the
use of non-original accessories and spare parts. Modifications
in design of the product relieve the seller from responsibility
for warranty works. The warranty dös not cover cosmetic
damage, that dösn’t hinder normal operation of the product.
4) CONDTROL GmbH reserves the right to decide on
replacement or repair of the device.
5) Other claims not mentioned above, are not covered by the
warranty.
6) After holding warranty works by CONDTROL GmbH warranty
period is not renewed or extended.
7) CONDTROL GmbH is not liable for loss of profit or
inconvenience associated with a defect of the device, the
rental cost of alternative equipment for the period of repair.
This warranty applies to German law except provision of the
United Nations Convention on contracts for the international
sale of goods (CISG).
In warranty case please return the product to retail seller or
send it with defect description to the following address:
Laser beam is on.
Short press
3 times.
(Vector 60)
Point to point measurement (Vector 80 only)
Symbol will appear on display.
CONDTROL GmbH
Wasserburger Strasse 9
84427 Sankt Wolfgang
Germany
Short press
5 times.
(Vector 80)
Laser beam is on.
Short
press
8 times.
Short press
Make
the
1st
measurement
(hypotenuse).
Short press
Make the 1st measurement (distance
to point A).
Short press
Make
the
2nd
measurement
(cathetus 1).
Short press
Make
the
2ndmeasurement
(distance to point B).
CARE AND MAINTENANCE
Attention! The instrument is a precise device and requires
careful handling. The following recommendations will extend
the life of the product:
- Do not point the product at the sun.
- Protect the product from bumps, falls, and excessive
vibration; do not let liquids, construction dust and foreign
objects get inside the product.
- Do not expose the product to extreme temperatures.
- If liquids get inside the product first remove the batteries,
then contact the service center.
- Do not store or use the product under high humidity
conditions for a long time.
- Clean the product with soft wet cloth.
- Keep device optics clean and protect it from mechanical
damage.
- Сarry out control measurements occasionally, especially if
the product is subject to excessive mechanical or other impact,
before and after taking important measurements.
- Hypotenuse
- Cathetus 1
UTILIZATION
Expired tools, accessories and package should be passed
for waste recycle. Please send the product to the following
address for proper recycle:
- Cathetus 2
– distance to point A
(measured)
– distance to point B
(measured)
CONDTROL GmbH
Wasserburger Strasse 9
84427 Sankt Wolfgang
Germany
Short press
Exit the mode.
– distance between points A
and B (calculated)
Calculation of distance by 3 additional measurements - sum
of cathetuses (Pythagoras 2)
Do not throw the product in municipal waste!
According to European directive 2002/96/ЕC expired
measuring tools and their components must be collected
separately and submitted to environmentally friendly recycle
of wastes.
Short press
Exit the mode.
Symbol will appear on display.
Memory
Laser beam is on.
Short press
4 times.
(Vector 60)
Enter memory. A number of saved
measurement/calculation results is
Short press
6 times.
(Vector 80)
Long press
for 1 sec.
reflected on symbol on the
Short press
Make
the
1st
measurement
(hypotenuse 1).
display.
Short press
Make
the
2nd
measurement
(cathetus).
View
saved
measurement/
Short press
calculation results.
Short press
Make
the
3rd
measurement
(hypotenuse 2).
Short press
Exit the mode.
– cathetus (measured)
Bluetooth
Bluetooth function is always on by default. Symbol is
permanently shown on the display.
Activate Bluetooth in the smartphone, tablet PC or laptop. For
further operation use application Smart Measure CONDTROL.
– hypotenuse 2 (measured)
– cathetus (calculated)
Short press
Exit the mode.