Текст страницы
WARRANTY
EN
DE
Laser level
Kreuzlinienlaser
DELIVERY PACKAGE
Laser level – 1 pc.
Battery (3,7V 4000 mAh Li-Ion) – 2 pcs.
Lifting platform – 1 pc.
Charger – 1 pc.
User manual – 1 pc.
Pouch – 1 pc.
Niveau laser
FR
Vertical line
Use a plumb bob as a reference of a vertical line. Put the laser
level at 1.5m distance from the plumb bob. (Fig. E).
1. Move the switch bar on position ON, and align vertical laser
line with the low point of plumb bob.
2. If deviation between the laser line and the plumb line
exceeds 0.3 mm per 1m of plumb bob length (for a 2.5m plumb
bob deviation shouldn’t exceed 0.7 mm) – please contact the
service center.
ACCURACY CHECK
Horizontal line
Accuracy check of horizontal line is carried out by 2 walls
located opposite each other at a 5m distance.
1. Put the laser level to one of the walls as close as possible
(Figure A). Move the switch bar to position ON and switch
on both vertical and horizontal planes. Rotate the laser level
so that laser emitters are located opposite to the near wall
and laser lines cross each other. Mark location of laser lines
crossing as А1. Mark location of laser lines crossing on another
wall as B1.
Livello laser
IT
Лазерный нивелир
RU
building areas.
BEFORE START OPERATION
Power supply
The laser level is powered by 3.7V 4000 mAh Li-Ion
rechargeable battery included in the delivery package.
PRODUCT DESCRIPTION
Laser level Boden 3D CONDTROL is designed for projecting and
controlling of vertical and horizontal planes and lines.
The laser level has 2 operating modes:
- automatic leveling, which allows to automatically
compensate irregularities within self-leveling range up to 3°.
- locked compensator, to project inclined planes and lines;
Pulse mode allows to increase working range of the laser level
by using the laser receiver or to work when laser is hard to
define in bright lighting conditions.
The laser level is suitable for use at both indoor and outdoor
building areas.
E
A
8
1
5m
2
1.5m
5
2. Rotate the laser level by 90°, measure deviation of a laser
line from point В1 (Figure B). If deviation exceeds 1.5 mm –
please contact the service center.
Install/charge the Li-ion battery
Install the battery in the battery compartment.
Use only the battery included in the delivery package.
If a power indicator on the left is flashing blue, charge the
battery.
The battery should be charged in the following way:
1) Remove the battery from the device.
2) Use charger, included in the delivery package, to connect
the battery to external power source. The power indicators on
the battery will be flashing blue while charging.
3) The battery charging time is about 3 hours.
4) As soon as the charging time runs out, the power indicators
will stop flashing. Disconnect the charger and put the battery
in the battery compartment.
It is allowed to charge the battery installed in the battery
compartment.
All CONDTROL GmbH products go through post-production
control and are governed by the following warranty terms. The
buyer’s right to claim about defects and general provisions of
the current legislation do not expire.
1) CONDTROL GmbH agrees to eliminate all defects in the
product, discovered while warranty period, that represent the
defect in material or workmanship in full volume and at its own
expense.
2) The warranty period is 24 months and starts from the date
of purchase by end consumer (see the original supporting
document).
3) The Warranty doesn’t cover defects resulting from wear
and tear or improper use, malfunction of the product caused
by failure to observe the instructions of this user manual,
untimely maintenance and service and insufficient care, the
use of non-original accessories and spare parts. Modifications
in design of the product relieve the seller from responsibility
for warranty works. The warranty does not cover cosmetic
damage, that doesn’t hinder normal operation of the product.
4) CONDTROL GmbH reserves the right to decide on
replacement or repair of the device.
5) Other claims not mentioned above, are not covered by the
warranty.
6) After holding warranty works by CONDTROL GmbH warranty
period is not renewed or extended.
7) CONDTROL GmbH is not liable for loss of profit or
inconvenience associated with a defect of the device, rental
cost of alternative equipment for the period of repair.
7
6
B
3
OPERATION
Install the device on a firm and stable surface, lifting platform
or tripod. Move the switch bar to select the required operation
mode.
4
This warranty applies to German law except provision of the
United Nations Convention on contracts for the international
sale of goods (CISG).
In warranty case please return the product to retail seller or
send it with description of defect to the following address:
1) Automatic leveling
Move the switch bar to position ON.
The laser level will switch on.
H-line is on.
Short press to switch on the required laser lines.
CONDTROL GmbH
Im Wiegenfeld 4
85570 Markt Schwaben
Germany
Boden 3D
Short press to switch on/off the pulse mode.
Move the switch bar to position OFF to switch off the laser
level.
3. Repeat actions described in point 2 twice, rotating the laser
level in one direction.
4. Install the laser level closer to the opposite wall. Mark
location of laser lines crossing as В2 (points В1, В2 must be
located at the same vertical) (Figure C).
8
9
EN User manual 1
DE Bedienungsanleitung 2
FR Mode d’emploi 3
IT Manuale dell’utente 4
RU Руководство по эксплуатации 5
2) Projection of inclined planes
Move the switch bar to position OFF.
C
LASER
LASER
1 – Laser beam
exit windows
2 – Control panel
3 – Switch bar
4 – Battery
5 – Battery release
button
6 – Battery charge
indicators
7 – Type-C
charging port
8 – Tripod thread 1/4’’
9 – Tripod thread 5/8’’
Press and hold during 3 seconds. H-line is on.
Laser line is flashing every 5 seconds.
Boden 3D
Laser level EN
Control panel
LASER
User manual
Short press to switch on the required laser lines.
After all combinations of lines are switched on, the next short
LASER
press will switch off the laser level.
LASER
1
2
Congratulations on your purchase of laser level Boden 3D
CONDTROL. Safety regulations can be found in this user
manual and should be carefully read before you use the device
for the first time.
Press to switch on/off the pulse mode.
- Switch on/off the laser lines
- Switch on/off the pulse mode
5. Rotate the laser level by 180°and mark location of laser lines
crossing on the opposite wall as A2 (points A1, A2 must be
located at the same vertical) (Figure D).
6. Measure distances dA, dB between points А1, А2 and В1,
В2 accordingly (Figure D). If difference between values dA, dB
exceeds 3 mm – please contact the service center.
TECHNICAL SPECIFICATIONS
D
CARE AND MAINTENANCE
Attention! This laser level is a precise optic-mechanical device
and requires careful handling. Before starting work, as well
as after mechanical influences (falling, bumps), check the
accuracy of the device.
Observation of the following recommendations will extend
the life of the device:
- Store the device, spare parts and accessories away from
children and unauthorized people.
- Transport the device with locked compensator only.
- Protect the device from bumps, falls, and excessive vibration;
do not let moisture, construction dust and foreign objects get
inside the device.
- In case moisture gets inside the device, first of all, remove the
batteries and then contact the service center.
- Do not store or use the device for a long time in high humidity
conditions.
- Check the accuracy of the device occasionally (check the
paragraph «Accuracy check»).
- Clean the device with a soft wet cloth. Do not use harsh
chemicals, cleaning solvents or cleaning agents.
- Wipe the laser aperture with a soft lint-free cloth and
isopropyl alcohol.
- Remove the Li-ion battery or alkaline batteries from the
device before connecting the charger, otherwise the device
may fail.
Failure to observe the following rules may lead to electrolyte
leakage from the batteries and failure of the device:
- Remove the battery from the device, if it’s not used for a
long time.
- Do not leave discharged battery in the device.
- Avoid heating the battery to avoid the risk of explosion and
electrolyte leakage. In case of liquid contact with skin, wash
it immediately with soap and water. In case of contact with
eyes, flush with clean water during 10 minutes and consult the
doctor.
Working range / with receiver*
30/60 m
Accuracy
±0.3 mm/m
Self-leveling range
± 3°
UTILIZATION
Distance between horizontal
laser line and floor
18 mm
SAFETY REGULATIONS
The user manual should be read carefully before you use the
device for the first time. Unintended use of the device can
be dangerous for human’s health and cause serious injury.
Keep this user manual. If the device is given to somebody for
temporary use, be sure to enclose user manual to it.
- Do not misuse the device.
- Do not remove warning signs and protect them from abrasion,
because they contain information about safe operation of the
device.
Laser radiation!
Do not stare into beam
Class 2 laser
<1 mW 515 nm
IEC 60825-1: 2007-03
Expired tools, accessories and package should be passed
for waste recycle. Please send the product to the following
address for proper recycle:
Continuous working time
- with one laser emitter switched on
- with all laser emitters switched on
20 hours
5 hours
Note: To increase the operating time and avoid the risk of
unintentional blinding switch on the laser only before start
operation.
If operated near objects or airflows different from the
environment temperature the laser line may tremble due to
heterogeneity of the atmosphere. The longer the distance, the
more trembling can be observed.
The width of the laser line increases with the increasing of the
operating distance. The marking should be made along the
axis of the laser line. For maximum accuracy, use the middle
portion of the laser line.
It should be noted that the shape of the laser line on the
object’s surface (e.g. walls, ceilings) depends on the curvature
and slope of the surface relative to the laser plane.
Operating temperature
-10°C ... +40°C
Storage temperature
-15°C ... +50°C
Relative humidity
90%
CONDTROL GmbH
Im Wiegenfeld 4
85570 Markt Schwaben
Germany
Dust and water protection rate
IP54
Tripod thread
1/4’’ and 5/8’’
Laser
Class II 515 nm
< 1 mW
Do not throw the product in municipal waste!
According to European directive 2002/96/ЕC expired
measuring tools and their components must be collected
separately and submitted to environmentally friendly recycle
of wastes.
Battery
3.7V 4000 mAh
Li-Ion rechargeable
Dimensions
147х91х136 mm
Weight
728 g
* The working range may differ from the declared depending
on the lighting conditions.
1
- Do not look into the laser beam or its reflection, with
unprotected eye or through an optical instrument. Do not
point the laser beam at people or animals without the need.
You can dazzle them.
- To protect your eyes close them or look aside.
- Always install the product in such a way, so that the laser line
is below or above the eye level.
- Do not let unauthorized people enter the zone of product
operation.
- Store the product beyond reach of children and unauthorized
people.
- It is prohibited to disassemble or repair the product yourself.
Entrust product repair to qualified personnel and use original
spare parts only.
- Do not use the product in explosive environment, close to
flammable materials.
- Avoid heating the batteries to avoid the risk of explosion and
electrolyte leakage. In case of liquid contact with skin, wash
it immediately with soap and water. In case of contact with
eyes, flush with clean water during 10 minutes and consult
healthcare practitioner.