Текст страницы
26 | English
loss of performance or atypical behaviour may occur upon
switch-on.
Please check the suitability of the power generator you are
using, particularly with regard to the mains voltage and fre-
quency.
u Products that are only sold in AUS and NZ: Use a resid-
and an increased risk of losing control of the power
tool, which can lead to kickback.
For cutting stone, it is best to use a diamond cutting disc.
When using the extraction guard for cutting with a cutting
guide (23), the dust extractor must be approved for extract-
ing stone dust. Suitable dust extractors are available from
Bosch.
ual current device (RCD) with a nominal residual current
of 30 mA or less.
u Pay attention to the mains voltage. The voltage of the
power source must match the voltage specified on the
rating plate of the power tool.
Switching on/off
To start the power tool, push the on/off switch (4) forward.
To lock the on/off switch (4) in position, push the on/off
switch (4) forward and down until it clicks into place.
To switch off the power tool, release the on/off switch (4);
or, if the switch is locked, briefly push the on/off switch (4)
backward and down and then release it.
u Always check abrasive tools before using them. The
abrasive tool must be fitted properly and be able to
move freely. Carry out a test run for at least one
minute with no load. Do not use abrasive tools that are
damaged, run untrue or vibrate during use. Damaged
abrasive tools can burst apart and cause injuries.
Maintenance and Service
Switch on the power tool
and position it with the
front part of the cutting
guide on the workpiece.
Move the power tool with a
moderate feed motion that
is suited to the material be-
ing machined.
When cutting especially
hard materials such as con-
crete with a high pebble content, the diamond cutting disc
can overheat and become damaged as a result. This is
clearly indicated by circular sparking, rotating with the dia-
mond cutting disc.
If this happens, stop cutting and allow the diamond cutting
disc to cool down by running the power tool for a short time
at maximum speed with no load.
If work is noticeably slower and with circular sparking, this
indicates that the diamond cutting disc has become blunt.
You can resharpen the disc by briefly cutting into abrasive
material (e.g. lime-sand brick).
Cutting other materials
Maintenance and Cleaning
u For cutting materials such as plastic, composite ma-
u Pull the plug out of the socket before carrying out any
work on the power tool.
u To ensure safe and efficient operation, always keep
the power tool and the ventilation slots clean.
u In extreme conditions, always use a dust extractor if
terials, etc. with bonded cutting discs or Carbide Multi
Wheel cutting discs, always use the protective guard
for cutting (8) or the protective guard for grinding (7)
with a fitted cover for cutting (11). You can achieve
improved dust extraction by using the extraction
guard with a cutting guide (23).
Working with Diamond Annular Cutters
u Only use dry diamond annular cutters.
u Always fit the hand guard (16) when working with dia-
possible. Blow out ventilation slots frequently and in-
stall a residual current device (RCD) upstream. When
machining metals, conductive dust can settle inside the
power tool, which can affect its protective insulation.
Store and handle the accessories carefully.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by an
after-sales service centre that is authorised to repair Bosch
power tools.
mond annular cutters.
Do not place the diamond annular cutter parallel to the work-
piece. Plunge it into the workpiece at an angle and in a circu-
lar motion. This will allow you to achieve optimal cooling and
ensure a longer tool life for the diamond annular cutter.
After-Sales Service and Application Service
Information on structural design
Recesses in load-bearing walls are subject to country-spe-
cific regulations. These regulations must be observed under
all circumstances. Seek advice from the responsible struc-
tural engineer, architect or construction supervisor before
starting work.
Start-up
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
When operating the power tool using a mobile generator that
does not have sufficient reserve capacity or an adequate
voltage control system with inrush current boost converter,
1 609 92A 765 | (17.03.2022)
Bosch Power Tools